Terazid G-33 – universal primer for plasters

DECLARATION OF PERFORMANCE
According with Regulation (EU) №305/2011

TERAZID G-33

№ 20130709-56-D

1. Unique identification code of product type:
TERAZID G-33

2. Type, batch, or serial number or other element allowing identification of the construction product as required under Article 11, paragraph 4 of Regulation (EU) №305/2011:
Acryl-polymer primer for facade finishing coats (batch number printed on the package)

3. Intended use or uses of the construction product in accordance with the applicable harmonized technical specification, as foreseen by the manufacturer:
Universal acrylic-based dispersion for priming the surface before applying facade plasters.

4. Name, registered trade name or registered trademark, and contact address of the manufacturer as required under Article 11, paragraph 4 of Regulation (EU) №305/2011:
TERAZID Ltd.
5 „5004” Str., Gara Iskar, Sofia 1528, Bulgaria
Tel.: +359 2 979 9971
E-mail: office@terazid.com

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12, paragraph 2 of Regulation (EU) №305/2011:
Not applicable.

6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Regulation (EU) №305/2011 for construction products, Annex V:
System 2+

7. In case of the declaration of performance concerning a construction product for which a European Technical Assessment was issued:
ETAG 004 — The notified body 1020 – Technical and Test Institute For Construction Prague has issued European Technical Assessment ETA-13/0214 according to ETAG 004.
The notified body has performed:

• Initial inspection of the factory and factory production control

• Continuous surveillance, assessment, and approval of the factory production control

The notified body has issued the EC Certificate of Factory Production Control №1020-CPD-060037435.
This certificate attests that all provisions concerning the attestation of factory production control, described in ETA-13/0214, were applied.

8. Declared performance:

TERAZID Ltd. 5 “5004” Str. Gara Iskar, Sofia, Bulgaria
Essential characteristics	Performance	Harmonized technical specification
Reaction to fire	Euroclass C	BDS EN 13820; BDS EN 15824, p. 4.7.
Density	1290 kg/m³	BDS EN ISO 2811-1
Adhesion with the base	1.05 N/mm²	BDS EN 24624
Time for drying	4 h	BDS EN ISO 3678
pH at 20°C	7	BDS EN ISO 787-9
Content of volatile organic compounds /VOC/	2.03 g/l < 30 g/l	BDS EN ISO 11890-2

9. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8.
This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

TECHNICAL DATA SHEET

TERAZID G-33

Universal Primer for Decorative Facade Plasters

High-quality penetrating primer for polymer, silicate, and silicone facade plasters

---

PURPOSE

TERAZID G-33 is a ready-to-use primer based on acrylic dispersion with added fillers.
It is used to prepare the surface before applying various types of facade plasters.

The primer:

• Maintains the “breathing” ability of the surface by ensuring excellent vapour permeability

• Equalizes water absorption across the working area

• Provides a dust-free surface

• Improves adhesion with different decorative coatings

After drying, TERAZID G-33 forms a white or coloured film, making it an ideal base for structural plasters with decorative “dragged” or “scratched” effects.
Its original white colour also allows easy tinting to match the finishing coatings.

TERAZID G-33 is a component of the External Thermal Insulation Composite System TERAZID BIO CLIMA, approved with ETA – 13/0214.

---

PROPERTIES

• Ready-to-use

• Vapour-permeable

• Water-repellent

• Improves adhesion with the base

---

PREPARATION OF THE BASE

The base must be:

• Dry

• Strong

• Free of grease, dust, and cracks

The surface should be smooth and free of holes.
When repairing facade surfaces, unstable areas must be removed, and old paint or grease spots thoroughly washed.
Repaired sections must achieve similar strength and bearing capacity as the surrounding old base before priming.

---

CHARACTERISTICS AND TECHNICAL DATA

• Colour: According to catalogue

• Base: Acrylic dispersion

• Density: 1290 kg/m³

• Work temperature: +5°C to +30°C

• Complete drying time: 4 hours

• Content of non-volatile substances: 9.62%

• Adhesion with concrete: 1.05 N/mm²

---

APPLICATION AND PROCESSING

Before use, stir the product thoroughly using a mechanical stirrer, without adding water or any dilution.
Apply TERAZID G-33 in one even layer, using a painting roller or brush with smooth movements.

Subsequent operations (such as plaster application) should start at least 24 hours after primer application.

---

CONSUMPTION

• From 0.150 l/m² to 0.220 l/m², depending on the base’s water absorption and roughness.

---

TOOLS FOR WORK

• Electrical drill and stirrer

• Roller-brush

• Brush

---

WEATHER CONDITIONS AT WORK

The minimum 24-hour temperature of the air and base should not be lower than +5°C, and the maximum should not exceed +30°C.
Do not apply when there is rain, strong wind, or when rain is forecasted. Avoid applying under direct sunlight and strong wind.

---

FORM OF DELIVERY

• Liquid in plastic packs of 1.4 kg, 5 kg, and 20 kg.

---

NOTES

• Characteristics and technical data in this Technical Data Sheet are defined at a standard temperature of 20°C and relative humidity of 50%.
  In other weather conditions, the technological times for some processes may be shorter or longer.

• The information is based on the manufacturer’s practical experience and technical laboratory tests.

• Do not mix with other building materials.

• All hazard and precautionary statements about TERAZID G-33 can be found in the product’s Safety Data Sheet.

---

STORAGE

• Shelf life: 12 months in originally sealed packages.

• Storage conditions: Store at temperatures from +5°C to +30°C.
  Protect from freezing and direct sunlight.

CE
TERAZID Ltd.
5 “5004” Str. Gara Iskar, Sofia, Bulgaria
ETAG 004
NB 1020
DoP № 20130709-56-D
TERAZID G-33
Universal primer for decorative finishing coats
Reaction to fire	Euroclass C
Density	1290 kg/m³
Adhesion with the base	1.05 N/mm²
Content of volatile organic compounds /VOC/	2.03 g/l < 30 g/l
pH at 20°C	7
Time for drying	4 h

The manufacturer recommends checking the suitability of the product in the Technical Data Sheet. The same is responsible for the product quality, but not for the ways and conditions of its applying. The information into the present Technical Data Sheet is reliable but only if the product is used under stated conditions. The responsibility of any other usage of the product, including its usage in a combination with any other product or a process, is borne by the user.

MATERIAL SAFETY DATA SHEET
According to (EU) 830/2015

TERAZID G-33

1. Identification of the Substance/Mixture and of the Company

1.1. Product identifier – TERAZID G-33 1.2. Application of the substance Acryl-polymer primer for facade finishing coats. 1.3. Details of the supplier of the safety data sheet TERAZID Ltd. 5, 5004 Street, Gara Iskar 1528 Sofia, Bulgaria tel. +3592/9799971, office@terazid.com 1.4. Emergency telephone number 112 UMHATEM “Pirogov” (toxicology) – +3592/9154409; +3592/9154233

2. Hazards Identification

2.1. Classification of the substance or mixture – Classification in accordance with the Regulation (ЕО) 1272/2008 – CLP The product is not classified as „dangerous“. 2.2. Label elements Precautionary statements: P101 – If medical advice is needed, have product container or label at hand. P102 – Keep out of reach of children. P262 – Do not get in eyes, on skin, or on clothing. P305 + P351 + P313 – IF IN EYES: Rinse cautiously with water for several minutes. Get medical advice/attention. P280 – Wear protective gloves/protective clothing/eye protection/face protection. P301 + P311 – IF SWALLOWED: Call a POISON CENTER or doctor/physician. P410 – Protect from sunlight. P401 – Store at temperatures higher than +5°C. 2.3. Other hazards None. For all warnings and recommendations, see Section 15.

3. Composition/information on ingredients

General chemical description – Acrylic-polymer dispersion, containing fine mineral fillers and modified additives. Information of the substances in accordance with CLP 1272/2008/EC Does not contain products, presenting in this section.

4. First Aid Measures

4.1. Description of the first aid measures Inhalation – Remove the person to fresh air. If the symptoms continue, immediately seek for qualified medical help. Skin contact – Immediately rinse the area of the contact with plenty of water, then wash it thoroughly with soap and water. Eye contact – Rinse with plenty of water for a period of at least 15 minutes and open eyelid. Seek for qualified medical help. Ingestion – Wash the mouth and the throat. Drink plenty of water. Seek for qualified medical help. 4.2. Most important symptoms and effects, both acute and delayed None. 4.3. Indication of any immediate medical attention and special treatment needed – see p. 4.1.

5. Firefighting Measures

TERAZID G-33 is non-combustible and prevents flames from spreading. Does not support combustion of other products. 5.1. Extinguishing media Water mist, water spray – sprayer, dry chemical, foam, carbon dioxide. Inappropriate extinguishing media – water under pressure. 5.2. Special hazards, arising from the substance or mixture – Non known 5.3. Advice for firefighters – Standard protective equipment when extinguishing a fire.

6. Accidental Release Measures

6.1. Personal precautions, protective equipment and emergency procedures Gloves, masks, protective clothing for work. Contact with skin and eyes should be avoided. 6.2. Environmental precautions Prevent this product from release in the environment. Measures should be taken for preventing contamination of surface and underground watercourses, soil, as well as falling into the drains. In the event of an accident and/or spill of the product, measures for localization and limitation should be taken, and the collected amount of the product should be temporarily stored into a special, tightly closed and labeled containers, and after that they should be transferred to people, holding permits under the Article 37 of the Waste Management Act (publication SG, issue 53, 2012). 6.3. Methods and materials for containment and cleaning up The spilled amount should be mechanically removed, and then the place should be washed thoroughly with water in accordance with the measures under art.6.2. Collected amount should be stored in special, tightly closed and labeled containers and to be temporarily stored on the territory of the company, and after that they should be transferred to people, holding a permit under the Waste Management Act (WMA).

7. Handling and Storage

7.1. Precautions for safe handling The product should be used only according to its main purpose. Avoid skin and eye contact. Keep the package tightly closed after usage. 7.2. Conditions for safe storage, including any incompatibilities It should be stored in ventilated and dry places, into the originally sealed containers. Temperatures lower than +5C and higher than +40C should be avoided. It should be separately stored from food and drinks. 7.3. Specific Usage There is no specific usage. It should be used only according to its main purpose.

8. Exposure Controls/Personal Protection

8.1. Control parameters – No special protection measures are necessary. 8.2. Exposure controls 8.2.1. Respiratory protection – prolonged inhalation of fumes should be avoided. 8.2.2. Skin protection – skin contact should be avoided, wear protective gloves. Clothing, soaked with the product should be changed. 8.2.3. Eye protection – eye contact should be avoided, wear safety glasses. 8.2.4. Common protection – it should be stored away from food, drinks and food for animals.

9. Physical and Chemical Properties

9.1. Information on basic physical and chemical properties

• Appearance: Liquid material

• Odour: Light

• pH at 20°C: 7.0

• Density: 1290 kg/m³

• Solubility: Partial

• Explosive properties: Non-explosive

10. Stability and reactivity

10.1. Reactivity – no hazardous reactions. 10.2. Chemical stability – the product is stable under storage and usage in accordance with the indications. 10.3. Possibility of hazardous reactions – in accordance with section 10.1. 10.4. Conditions to avoid – temperatures lower than +5C and higher than 40C should be avoided. 10.5. Incompatible materials – no data. 10.6. Hazardous decomposition products – it is unlikely to release carbon oxides at fire.

11. Toxicological information

11.1. Information for the toxicological effects Toxicological properties of the product are not tested. The product is classified under the conventional method in accordance with Regulation (ЕО) 1272/2008 – CLP. On the basis of its composition, the product can be defined as not having any toxic effects under a proper usage. Ingestion – The product is not hazardous of acute poisoning. Inhalation – It is not considered as harmful at normal conditions. Skin contact – Prolonged contact may cause irritation. Eye contact – Prolonged and repeated contact may cause irritation and redness.

12. Ecological information

12.1. Toxicity Polymer dispersion data: Toxicity to fish: LC50 (96 h) > 100 mg/l, (OECD Directive 203, static) Aquatic invertebrates: ЕC50 (48 h) > 100 mg/l, (OECD Directive 202, part 1, static) Aquatic plants: ЕC50 (72 h) > 100 mg/l, (OECD Directive 201) Micro-organisms/Effect of the active sediment: ЕC20 (0,5 h) > 100 mg/l, active sediment (DIN EN ISO 8192-OECD 209-88/302/EEC, P. C) On the basis of the experience, the product is not expected to be hazardous to the environment. 12.2. Persistence and degradability – No data. 12.3. Bio-accumulative potential – Accumulation in the organism is not expected. 12.4. Mobility in soil This product is not biologically mobile. 12.5. Results of PBT and vPvB assessment – the product meets the criteria of PBT (persistent, bio-accumulative and toxic) and vPvB (very persistent and very bio-accumulative). 12.6. Other adverse effects No data. General information: Do not allow the product to enter into the soil or natural watercourses.

13. Disposal considerations

Product waste, such as residual quantities and packages, should be collected into a special, tightly sealed and labelled containers, temporarily stored, and after that to be transferred to people, holding a permit in accordance with article 37 of the Waste Management Act (publication SG, issue 53, 2012). Waste code, in accordance with Regulation №2 from 23.07.2014 for Waste Classification: 08 01 20 – liquid suspensions of paints, others than those mentioned in 08 01 19 Waste Packages code: 15 01 02 – plastic packages. Completely empty the packages and dispose them in accordance with the local regulations.

14. Transport information

It is not a hazardous load, in accordance with RID, ADR, ADNR, IMDG, IATA-DGR. It should be transported under the respective rules for transportation, concerning the respective type of transport and ensuring the safety of the load.

15. Regulatory information

15.1 Content of volatile organic compounds /VOC/, in accordance with the Ordinance on limiting the emissions of volatile organic compounds in the use of organic solvents in certain paints, varnishes and auto reparatory products, category А, sub point c) 2.03 g/l < 30 g/l 15.2 Classification and labelling of the product in accordance with Regulation (ЕО) 1272/2008 – CLP /full text of the codes/ GHS Pictograms: No. Signal word: No. Recommendations for danger (N – codes): None. Hazard statements (H – codes): None. Precautionary statements (P – codes): P101 – If medical advice is needed, have product container or label at hand. P102 – Keep out of reach of children. P262 – Do not get in eyes, on skin, or on clothing. P305 + P351 + P313 – IF IN EYES: Rinse cautiously with water for several minutes. Get medical advice/attention. P280 – Wear protective gloves/protective clothing/eye protection/face protection. P301 + P311 – IF SWALLOWED: Call a POISON CENTER or doctor/physician. P410 – Protect from sunlight. P401 – Store at temperatures higher than +5°C.

15.3. LEGISLATION

National Legislation:

• Law of Protection from the Harmful Impact of the Chemical Substances and Preparations

• Environmental Protection Law

• Health and Safety at Work Act

• Ordinance №3 on the Minimum Requirements for Safety and Protection of Workers When Using Personal Protective Equipment at the Workplace

• Waste Management Act

• Ordinance №2 from 23.07.2014 for Waste Classification

• Ordinance on the Order and Method of Classification, Labelling, and Packaging of Chemical Substances and Preparations

European Legislation:

• Regulation (EC) 1272/2008 – CLP from 16th December 2008, concerning the classification, labelling, and packaging of substances and preparations

• Regulation (EU) 830/2015 from 28th May 2015

16. Other Information

16.1. Indication of changes Format in accordance with Regulation (ЕО) 830/2015 from 28th May 2015 amending Regulation № 1907/2006 (REACH) of the European Parliament. 16.2. Training Advice In addition to the training programs on environment and health and safety of the workers, the companies need to be sure that their workers read, understand and apply the requirements of the MSDS. 16.3. Additional information See the application(s) of exposure scenarios for the following substances: The basic information of the exposure scenarios of the substances in the mixture are included in points 1, 2, 3, 8, 11 and 12.

16.4. Disclaimer

This safety data sheet and the data inside of it are based on industrial and commercial experience of many years and are fully complied with the current active legislation of the Republic of Bulgaria and the European Union. This safety data sheet is not intended to guarantee any specific properties and qualities of the product. The information inside of it is reliable but, on the circumstance, that the product is used in accordance with the indicated conditions and the application, specified on the package and/or in the technical literature. Responsibility of any other use of the product, including when using it in combination with another product or process is completely under the responsibility of the user. It is understood that the user is responsible for defining the appropriate precautions and for applying the legislation, concerning his own activity.