Top Mix Thermo – Adhesive and base-coat for EPS

DECLARATION OF PERFORMANCE
According with Regulation (EU) №305/2011

TOP MIX THERMO

№ 20130709-79-D

1. Unique identification code of product type:
TOP MIX THERMO

2. Type, batch, or serial number or other element allowing identification of the construction product as required under Article 11, paragraph 4 of Regulation (EU) №305/2011:
Adhesive and reinforcement base-coat plaster for insulation boards (batch number printed on the package)

3. Intended use or uses of the construction product in accordance with the applicable harmonized technical specification, as foreseen by the manufacturer:
Cement-based mixture for bonding and plastering of EPS thermal insulation boards

4. Name, registered trade name or registered trademark, and contact address of the manufacturer as required under Article 11, paragraph 4 of Regulation (EU) №305/2011:
TERAZID Ltd.
5 „5004” Str., Gara Iskar, Sofia 1528, Bulgaria
Tel.: +359 2 979 9971
E-mail: office@terazid.com

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12, paragraph 2 of Regulation (EU) №305/2011:
Not applicable.

6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Regulation (EU) №305/2011 for construction products, Annex V:
System 3, System 2+

7. In case of the declaration of performance concerning a construction product for which a European Technical Assessment was issued:

• BDS EN 12004 — Adhesives for tiles — Requirements, evaluation of conformity, classification, and designation

• BDS EN 13494 — Thermal insulation products for building applications — Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material

• BDS EN 13499 — Thermal insulation products for buildings — External thermal insulation composite systems (ETICS) based on expanded polystyrene — Specification

The notified body 1950 — The Research Institute of Building Materials (NIISM), Sofia, has performed initial type testing, based on samples provided by the manufacturer.

8. Declared performance

TERAZID Ltd. 5 “5004” Str. Gara Iskar, Sofia, Bulgaria
Essential characteristics	Performance	Harmonized technical specification
Reaction to fire	Class A1	BDS EN 13820
Density	1450 kg/m³	BDS EN 1015-6
Adhesion with the concrete base	570 kPa	BDS EN 1015-12
Bond strength with EPS slab	120 kPa	BDS EN 13494
Coefficient of water vapour permeability	2.9×10-9 g/m·d·Pa	BDS EN 1015-19
Coefficient of capillary absorption of water – c	0.38 kg/m²·h0.5	BDS EN 1062-3
Compressive strength	17.7 N/mm²	BDS EN 1015-11
Class C2 according to BDS EN 12004
Initial tensile bond strength	2.2 N/mm²	BDS EN 12004-2
Tensile bond strength after water immersion	1.3 N/mm²	BDS EN 12004-2
Tensile bond strength after heat treatment	1.9 N/mm²	BDS EN 12004-2
Tensile bond strength after 25 freeze-thaw cycles	1.0 N/mm²	BDS EN 12004-2

9. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8. This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

TECHNICAL DATA SHEET

TOP MIX THERMO

Adhesive and Reinforcement Base-Coat Plaster for Insulation Boards

Cement-based mixture for bonding and plastering of EPS thermal insulation boards

---

PURPOSE

TOP MIX THERMO is a cement adhesive and base-coat plaster based on grey cement, with added fine mineral fillers, reinforced mono fibres, and polymer additives. It is designed for bonding expanded polystyrene (EPS) boards to walls and ceilings for both interior and exterior insulation of buildings.
The material is suitable for constructing new walls as well as renovating old buildings.

Application of a protective reinforcement base-coat with TOP MIX THERMO prevents insulation boards from aging and protects them from weather influences. It ensures waterproofing and crack resistance of the finished layer while protecting the insulation layer from mechanical damage.
It creates an excellent base for decorative facade finishes with fine plaster or paint.

TOP MIX THERMO is a Class C2 product according to BDS EN 12004 – Adhesives for tiles – Requirements, evaluation of conformity, classification, and designation.

---

PROPERTIES

• Easy to apply

• Sufficient open time (for work)

• Cold resistant

• Impact resistant

• Vapour-permeable

---

PREPARATION OF THE BASE

TOP MIX THERMO has excellent adhesion to various construction surfaces, such as bricks, concrete, plasters, cement, and gypsum base-coats.
The base should be dry, well-cleaned, and strong. Application over oil (grease) stains, dust, and other contaminants is not allowed.
Old unstable plasters and coatings must be removed.

Bases with high absorption, such as aerated concrete or gypsum blocks, should be primed in advance with deeply penetrating primer TERAZID G-55.

---

CHARACTERISTICS AND TECHNICAL DATA

• Colour: Grey

• Base: Cement

• Density: 1450 kg/m³

• Work temperature: +5°C to +30°C

• Time for “maturing”: 6–7 minutes

• Time for bucket stay: About 5 hours

• Open time for work: 20 minutes

• Time for final bonding and subsequent operations: 7 days

• Recommended thickness of the base-coat layer: 4–5 mm

---

INSTRUCTIONS FOR APPLICATION AND PROCESSING

For complete dissolution of 25 kg of TOP MIX THERMO, approximately 6.5 litres of water are required.
In a pre-prepared container with water, the necessary amount of dry mixture is gradually poured and stirred using a mechanical mixer until a homogeneous mass is achieved.
The stirred mixture should be left to mature for 6–7 minutes, then stirred again before use.

Bonding:

• On smooth and flat surfaces, the prepared solution is applied like a comb using a notched mortar-board with edge sizes of 8–10 mm.

• On rough surfaces, the solution is applied around the entire outer rim of the insulation panel in a strip 4–5 cm wide, with additional “pillows” of adhesive in a few places on the inner side of the panel.

Note:
Additional fixing of the insulation with anchors can start no earlier than 24 hours after bonding (at temperatures not lower than 20°C).

Plastering:
After the boards are anchored, TOP MIX THERMO is used as a base-coat.
The solution is uniformly applied, and the reinforcement fiberglass mesh is embedded vertically, tightly pressed, and smoothed with a mortar-board.
The recommended thickness of the base-coat layer is 4–5 mm.

---

CONSUMPTION

• Bonding: 5.0–5.5 kg/m² depending on the base

• Plastering: 3.5–4.0 kg/m²

---

TOOLS FOR WORK

• Bucket

• Electrical drill and stirrer

• Trowel

• Mortar-board

• Lute

---

WEATHER CONDITIONS AT WORK

The minimum 24-hour temperature of the air and base should not be less than +5°C, and the maximum should not exceed +30°C.
Application is not recommended at high air humidity, during rainfall, or when rain is forecasted.

---

FORM OF DELIVERY

• Dry mixture in paper packages of 25 kg

---

NOTES

• Characteristics and technical data presented in this Technical Data Sheet are defined at a standard temperature of 20°C and a relative humidity of 50%.
  Under other weather conditions, the technological times for some processes may be shorter or longer.

• The product information is based on the manufacturer’s practical experience and technical tests performed in specialized laboratories.

• Do not mix with other building materials.

• All hazard and precautionary statements regarding TOP MIX THERMO can be found in the product’s Safety Data Sheet.

---

STORAGE

• Shelf life: 12 months in originally sealed packages

• Storage conditions: Store in a dry and ventilated area. It is recommended to store the product on pallets.

CE
TERAZID Ltd.
5 “5004” Str. Gara Iskar, Sofia, Bulgaria
EN 13499
NB 1020
DoP № 20130709-79-D
TOP MIX THERMO
Adhesive and reinforcement base-coat plaster for insulation boards
Reaction to fire	A1
Bulk density	1450 kg/m³
Bond strength with concrete base	570 kPa
Bond strength with EPS slab	120 kPa
Compressive strength	17.7 N/mm²
Coefficient of capillary absorption of water – c	0.38 kg/m²·h0.5
Coefficient of water vapour transmission	2.9×10-4 g/m²·d·Pa
Class C2 according to BDS EN 12004
Initial tensile bond strength	2.2 N/mm²
Tensile bond strength after water immersion	1.3 N/mm²
Tensile bond strength after heat treatment	1.9 N/mm²
Tensile bond strength after 25 freeze-thaw cycles	1.0 N/mm²

The manufacturer recommends checking the suitability of the product in the Technical Data Sheet. The same is responsible for the product quality, but not for the ways and conditions of its applying. The information into the present Technical Data Sheet is reliable but only if the product is used under stated conditions. The responsibility of any other usage of the product, including its usage in a combination with any other product or a process, is borne by the user.

MATERIAL SAFETY DATA SHEET
According to (EU) 830/2015

TOP MIX THERMO

1. Identification of the Substance/Mixture and of the Company

1.1. Product identifier – TOP MIX THERMO 1.2. Application of the substance Cement-based mixture for bonding and reinforcing of insulation boards 1.3. Details of the supplier of the safety data sheet TERAZID Ltd. 5, 5004 Street, Gara Iskar1528 Sofia, Bulgaria tel. +359 2 9799971, office@terazid.com 1.4. Emergency telephone number (EU) 112 UMHATEM “Pirogov” (toxicology) – +3592/9154409; +3592/9154233

2. Hazards Identification

2.1. Classification of the substance or mixture – Classification in accordance with Regulation (ЕО) 1272/2008 – CLP: The product is classified as „dangerous“. 2.2. Label elements Hazard pictograms:

Signal word: Danger!

Hazard statements: H315 – Causes skin irritation. H318 – Causes serious eye damage. H335 – May cause respiratory irritation. Precautionary statements: P101 – If medical advice is needed, have product container or label at hand. P102 – Keep out of reach of children. P261 – Avoid breathing dust/fume/gas/mist/vapours/spray. P280 – Wear protective gloves/protective clothing/eye protection/face protection. P302 + P352 – IF ON SKIN: Wash with plenty of soap and water. P332 + P313 – If skin irritation occurs: Get medical advice/attention. P305 + P351 + P315 – IF IN EYES: Rinse cautiously with water for several minutes. Get immediate medical advice/attention. P402 – Store in a dry place. 2.3. Other hazards Contains portland cement. When reacting with water, it creates an alkaline medium. Does not contain soluble Cr (VI) into a quantity greater than 0,0002 % within the period of storage. For all warnings and recommendations, see Section 15.

3. Composition/information on ingredients

General chemical description: Adhesive and base-coat plaster on the basis of portland cement, mineral fillers and modifying additives. Information of the substances in accordance with CLP 1272/2008/EC

CAS № EINECS №	Name	Concentration (%)	Signal word	H-codes
65997-15-1 266-043-4	Grey cement	20–40	Hazardous	H315, H318, H335

4. First Aid Measures

4.1. Description of the first aid measures Inhalation – Remove the person to fresh air. If the symptoms continue, immediately seek for qualified medical help. Skin contact – Immediately rinse the area of the contact with plenty of water, then wash it thoroughly with soap and water. Eye contact – Irrigate with plenty of water for a period of at least 15 minutes and open eyelid. Seek for qualified medical help. Ingestion – Do NOT induce vomiting. Seek for qualified medical help. 4.2. Most important symptoms and effects, both acute and delayed In contact with the eyes: irritation. In contact with the skin: redness, inflammation. 4.3. Indication of any immediate medical attention and special treatment needed – see p. 4.1.

5. Firefighting Measures

TOP MIX THERMO is non-combustible and non-explosive product. 5.1. Extinguishing media Water mist, water spray – sprayer, dry chemical, foam, carbon dioxide. Inappropriate means for extinguishing fire – Not known. 5.2. Special hazards, arising from the substance or mixture – Non known 5.3. Advice for firefighters: Autonomous respiratory equipment.

6. Accidental Release Measures

6.1. Personal precautions, protective equipment and emergency procedures Gloves, masks, protective clothing for work. Contact with skin and eyes should be avoided. 6.2. Environmental precautions Prevent this product from release in the environment. Measures should be taken for preventing contamination of surface and underground watercourses, soil, as well as falling into the drains. In the event of an accident and/or spill of the product, measures for localization and limitation should be taken, and the collected amount of the product should be temporarily stored into a special, tightly closed and labeled containers, and after that they should be transferred to people, holding permits under the Article 37 of the Waste Management Act. 6.3. Methods and materials for containment and cleaning up The spilled amount should be mechanically removed, by taking measure to prevent formation of high concentration of dust in the air. The amount in the form of dust or unhardened mixture should be rinses with water and soap. Collected amount should be stored in special, tightly closed and labeled containers and to be temporarily stored on the territory of the company, and after that they should be transferred to people, holding a permit under the Waste Management Act (WMA).

7. Handling and Storage

7.1. Precautions for safe handling The product should be used only according to its main purpose. Do not eat, drink or smoke during work. Avoid formation of dust and often ventilate the room. Avoid skin and eye contact. 7.2. Conditions for safe storage, including any incompatibilities It should be stored in ventilated and dry places, into the originally sealed pakcages. Temperatures lower than 0C and higher than +50C should be avoided. It should be separately stored from food and drinks. 7.3. Specific Usage There is no specific usage. It should be used only according to its main purpose.

8. Exposure Controls/Personal Protection

8.1. Control parameters Portland cement – permitted level of inhaled powder particles: 5 ppm/5 mg/m³ air/. 8.2. Exposure controls 8.2.1. Respiratory protection – use a mask preventing from inhaling dust, filter P2. 8.2.2. Skin protection – skin contact should be avoided, wear protective gloves. 8.2.3. Eye protection – eye contact should be avoided, wear safety glasses. 8.2.4. Common protection – it should be stored away from food, drinks and food for animals.

9. Physical and Chemical Properties

9.1. Information on basic physical and chemical properties

• Appearance: Fine powder

• Color: Grey

• Odor: None

• pH at 20°C: Approximately 7.5

• Density: 1450 kg/m³

• Solubility: Insoluble

• Explosive properties: Non-explosive

9.2. Other information – no data.

10. Stability and reactivity

10.1. Reactivity – the product reacts with the moisture and gets hardened. 10.2. Chemical stability – the product is stable under storage and usage in accordance with the indications. 10.3. Possibility of hazardous reactions – in accordance with section 10.1. 10.4. Conditions to avoid – it should be kept away from moisture at storage and transportation. 10.5. Incompatible materials – no data.

11. Toxicological Information

11.1. Information for the toxicological effects Toxicological properties of the product are not tested. The product is classified under the conventional method in accordance with Regulation (ЕО) 1272/2008 – CLP. On the basis of its composition, the product can be defined as not having any toxic effects under a proper usage. The product is not hazardous of acute poisoning. Ingestion – It is less likely that the ingestion will lead to reaction or long-term effect, but is recommended to be avoided. Inhalation – Dust can cause irritation in the nose, the throat and the lungs, leading to coughing. Skin contact – In combination with heat and sweat, the product can cause irritation, but is not absorbed through the skin. Eye contact – The product can cause serious eye damage.

12. Ecological Information

12.1. Toxicity It is not expected that the product is hazardous for the environment (LC50 toxicity in water – it is not defined). Adding large amounts of water, however, can lead to rising of pH and therefore it can appear to be toxic to aquatic organisms at certain conditions. 12.2. Persistence and degradability – No data. 12.3. Bio-accumulative potential – Low potential of bioaccumulation. 12.4. Mobility in soil Hard product with non-organic origin. 12.5. Results of PBT and vPvB assessment – the product does not meet the criteria of PBT (persistent, bioaccumulative and toxic) and vPvB (very persistent and very bio-accumulative). 12.6. Other adverse effects No data.

13. Disposal Considerations

Product waste, such as residual quantities and packages, should be collected into a special, tightly sealed and labeled containers, temporarily stored, and after that to be transferred to people, holding a permit in accordance with article 37 of the Waste Management Act (publication SG, issue 53, 2012). Waste code, in accordance with Regulation №2 from 23.07.2014 for Waste Classification: 10 13 – Waste from the production of cement, lime, gypsum and items and products, made of these materials. 10 13 14 – Waste concrete and concrete sediment. 15 01 – Packages. 15 01 10 – Packages, containing residues of hazardous substances or contaminated with hazardous substances. Completely empty the packages and dispose them in accordance with the local regulations– at the indicated places for paper waste.

14. Transport Information

It is not a hazardous load, in accordance with RID, ADR, ADNR, IMDG, IATA-DGR. It should be transported under the respective rules for transportation, concerning the respective type of transport and ensuring the safety of the load.

15. Regulatory information

15.1 Classification and labeling of the product in accordance with Regulation (ЕО) 1272/2008 – CLP /full text of the codes/ GHS Pictograms:

GHS05

GHS07

Signal word: Danger! GHS07 Recommendations for danger (N – codes): None. Hazard statements (H – codes): H315 – Causes skin irritation. H318 – Causes serious eye damage. H335 – May cause respiratory irritation. Precautionary statements (P – codes): P101 – If medical advice is needed, have product container or label at hand. P102 – Keep out of reach of children. P261 – Avoid breathing dust/fume/gas/mist/vapours/spray. P280 – Wear protective gloves/protective clothing/eye protection/face protection. P302 + P352 – IF ON SKIN: Wash with plenty of soap and water. P332 + P313 – If skin irritation occurs: Get medical advice/attention. P305 + P351 + P315 – IF IN EYES: Rinse cautiously with water for several minutes. Get immediate medical advice/attention. P402 – Store in a dry place.

15.2. LEGISLATION

National Legislation:

• Law of Protection from the Harmful Impact of the Chemical Substances and Preparations

• Environmental Protection Law

• Health and Safety at Work Act

• Ordinance №3 on the Minimum Requirements for Safety and Protection of Workers When Using Personal Protective Equipment at the Workplace

• Waste Management Act

• Ordinance №2 from 23.07.2014 for Waste Classification

• Ordinance on the Order and Method of Classification, Labeling, and Packaging of Chemical Substances and Preparations

European Legislation:

• Regulation (EC) 1272/2008 – CLP from 16th December 2008, concerning the classification, labelling, and packaging of substances and preparations

• Regulation (EU) 830/2015 from 28th May 2015

16. Other Informaiton

16.1. Indication of changes Format in accordance with Regulation (ЕО) 830/2015 from 28th May 2015 amending Regulation № 1907/2006 (REACH) of the European Parliament. 16.2. Training advice In addition to the training programs on environment and health and safety of the workers, the companies need to be sure that their workers read, understand and apply the requirements of the MSDS. 16.3. Additional information See the application(s) of exposure scenarios for the following substances: The basic information of the exposure scenarios of the substances in the mixture are included in points 1, 2, 3, 8, 11 and 12.

16.4. Disclaimer

This safety data sheet and the data inside of it are based on industrial and commercial experience of many years and are fully complied with the current active legislation of the Republic of Bulgaria and the European Union. This safety data sheet is not intended to guarantee any specific properties and qualities of the product. The information inside of it is reliable but, on the circumstance, that the product is used in accordance with the indicated conditions and the application, specified on the package and/or in the technical literature. Responsibility of any other use of the product, including when using it in combination with another product or process is completely under the responsibility of the user. It is understood that the user is responsible for defining the appropriate precautions and for applying the legislation, concerning his own activity.