Decora – Decorative mosaic plaster

DECORA

DECLARATION OF PERFORMANCE
According with Regulation (EU) №305/2011

№ 20130709-03-D

1. Unique identification code of product type:
DECORA

2. Type, batch or serial number or other element allowing identification of the construction product as required under Article 11, paragraph 4 of Regulation (EU) №305/2011:
Mosaic acryl-polymer finishing coat
Batch number printed on the package

3. Intended use or uses of the construction product in accordance with the applicable harmonized technical specification, as foreseen by the manufacturer:
Mosaic acryl-polymer mixture for protective and decorative coating on exterior and interior surfaces.

4. Name, registered trade name or registered trade mark and contact address of the manufacturer, as required under Article 11, paragraph 5 of Regulation (EU) №305/2011:
TERAZID Ltd.
5 „5004” Str., Gara Iskar, Sofia 1528, Bulgaria
Tel.: +359 2 9799971
E-mail: office@terazid.com

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12, paragraph 2 of Regulation (EU) №305/2011:
Not applicable.

6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Regulation (EU) №305/2011 for construction products, Annex V:
System 4

7. In case of the declaration of performance concerning a construction product covered by harmonized standard:
BDS EN 15824 – Specifications for external renders and internal plasters based on organic binders.

8. Declared performance

TERAZID Ltd.

5 “5004” Str. Gara Iskar, Sofia, Bulgaria

Essential characteristics	Performance	Harmonized technical specification
Reaction to fire	A2 – s1, d0	EN 13501-1
Density	1910 kg/m³	BDS EN 1015-6
Adhesion with the base	0.3 MPa	BDS EN 24624
Coefficient of water vapour transmission	65 g/m²·d V₂	BDS EN 15824
Coefficient of capillary absorption of water – c	2.65 kg/m²·h0.5 class W₂	BDS EN 15824
pH at 20°C	7.8	BDS EN ISO 787-9
Content of volatile organic compounds /VOC/	< 40 g/l	BDS EN ISO 11890-2

9. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8.
This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

 

DECORA

Decorative mosaic plaster

Ready-to-use mosaic acryl-polymer mixture for protective and decorative coating on exterior and interior surfaces

PURPOSE
DECORA is ready-to-use finishing coat, based on acrylic dispersion with added coloured marble and granite stones and preservatives. The product is used for making fine protective and decorative coating for facades and interior premises. This plaster is particularly suitable for making protective coatings in areas exposed on great mechanical loading, like socles, fences, inner columns, etc. It creates colourful waterproofed surface.
The product provides a possibility for an extremely wide variety of architectural solutions for facades and individual facade elements with a wide range of 90 different colours.

PROPERTIES
❖ ready-to-use
❖ vapour-permeable
❖ water-repellent
❖ resistant to different weather conditions
❖ UV-resistant
❖ great mechanical strength

PREPARATION OF THE BASE
The base must be dry, strong and free of grease, dust and cracks. The surfaces should be smooth and free of holes. If necessary, separate uneven elements of the facade should be filled with rough coating.
In case of repairing facade surfaces, unstable areas should be removed and the areas with old paint and grease spots should be carefully washed. Repaired sections must have the same strength and bearing capacity as the old base before priming. Base processing with the primer TERAZID G-33 before applying the plaster is required.

CHARACTERISTICS AND TECHNICAL DATA
▪ Colour: according to catalogue;
▪ Type: homogeneous granular mass;
▪ Density: 1910 kg/m³;
▪ Resistance of vapour passing: µ = 205;
▪ Minimal temperature of film formation: +5˚C;
▪ Resistance of rain: after 24 hours*
(at normal weather conditions – temperature of 20˚C and air humidity – 50 %)
▪ Bond strength with concrete after 7 days: 1.40 MPa;

APPLICATION AND PROCESSING
The application of the mosaic plaster DECORA should start at least 24 hours after priming the base with TERAZID G-33. When applied on large areas, the content of 2-3 buckets of DECORA should be mixed in a bigger container.
Before the application begins, the content in the bucket should be stirred with the help of a mechanic mixer. Rusty tools are not allowed to use.
If it is necessary, the plaster can be diluted with water but not more than 100 ml per 10 kg of plaster and the mixture is being stirred again.
The thickness of the coating is defined by the marble grains which are manually applied with the help of a plastic mortarboard.
When applying the material, its thickness is being aligned of about 1.5 times the size of the stones in the plaster. It takes about 10 minutes after that for becoming completely smooth as the stones are getting maximally tight to one another (without any pores) for achieving the desired final effect. If it is necessary, the process of smoothing is repeated a few times.

It is recommended to work on one surface (area) without interruption. No unfinished surfaces should be left after completing the work.
When applying on adjacent areas with different colours, they must be separated with paper tape to protect the already applied plaster from staining.
Before priming and applying the plaster, parts that are not going to be plastered should be covered.
DECORA should not be applied under direct sunlight or in areas exposed to strong air drafts.

CONSUMPTION
▪ 4 – 4.5 kg/m²

TOOLS FOR WORK
▪ mechanical mixer
▪ stainless trowel
▪ plastic mortarboard
▪ brush

WEATHER CONDITIONS AT WORK
The minimum 24-hour temperature of the base should not be less than +5˚C, and the maximum not higher than +40˚C.
The product should not be applied during rain, when rain is forecasted, or under direct sunlight and strong wind.

FORM OF DELIVERY
Paste in a plastic bucket of 10 kg and 25 kg.

NOTES
Characteristics and technical data of the product mentioned in this Technical Data Sheet are defined at a standard temperature of 20˚C and relative humidity of 50%.
In other weather conditions, the technological time for some of the processes mentioned above may be shorter or longer.
The information is based on the manufacturer’s practical experience and technical tests in specialized laboratories.
Do not mix with other building materials.
All hazard and precautionary statements regarding DECORA can be found in the product’s Safety Data Sheet.

STORAGE
12 months in the originally sealed package, stored in a dry place, without risk of freezing.

TERAZID Ltd.

5 “5004” Str. Gara Iskar, Sofia, Bulgaria

BDS EN 15824

NB 1950

DoP № 20130709-03-D

DECORA

Mosaic acryl-polymer finishing coat

Reaction to fire	A2 – s1, d0
Density	1910 kg/m³
Adhesion with the base	0.3 MPa
Coefficient of water vapour transmission	65 g/m²·d V₂
pH at 20°C	7.8
Coefficient of capillary absorption of water – c	2.65 kg/m²·h0.5 class W₂
Content of volatile organic compounds /VOC/	< 40 g/l

 

DECORA

SAFETY DATA SHEET
According to (EU) 830/2015

1. Identification of the Substance/Mixture and of the Company
1.1. Product identifier – DECORA
1.2. Application of the substance
Decorative mosaic facade plaster.
1.3. Details of the supplier of the safety data sheet
TERAZID Ltd.
5, 5004 Street, Gara Iskar
1528 Sofia, Bulgaria
tel. +3592/9799971, office@terazid.com
1.4. Emergency telephone number 112
UMHATEM “Pirogov” (toxicology) – +3592/9154409; +3592/9154233

2. Hazards Identification
2.1. Classification of the substance or mixture

• Classification in accordance with the Regulation (ЕО) 1272/2008 – CLP
  The product is not classified as “dangerous”.

2.2. Label elements
Precautionary statements:
P101 – If medical advice is needed, have product container or label at hand.
P102 – Keep out of reach of children.
P262 – Do not get in eyes, on skin, or on clothing.
P305 + P351 + P313 – IF IN EYES: Rinse cautiously with water for several minutes. Get medical advice/attention.
P280 – Wear protective gloves/protective clothing/eye protection/face protection.
P301 + P311 – IF SWALLOWED: Call a POISON CENTER or doctor/physician.
P410 – Protect from sunlight.
P401 – Store at temperatures higher than +5°C.

2.3. Other hazards
None.
For all warnings and recommendations, see Section 15.

3. Composition/information on ingredients
General chemical description – Acrylic-polymer dispersion, containing mineral fillers and modified additives.
Information of the substances in accordance with CLP 1272/2008/EC
Does not contain products, presenting in this section.

4. First Aid Measures
4.1. Description of the first aid measures
Inhalation – Remove the person to fresh air. If the symptoms continue, immediately seek for qualified medical help.
Skin contact – Immediately rinse the area of the contact with plenty of water, then wash it thoroughly with soap and water.
Eye contact – Rinse with plenty of water for a period of at least 15 minutes and open eyelid. Seek for qualified medical help.
Ingestion – Wash the mouth and the throat. Drink plenty of water. Seek for qualified medical help.

4.2. Most important symptoms and effects, both acute and delayed
None.

4.3. Indication of any immediate medical attention and special treatment needed – see p. 4.1.

5. Firefighting Measures
DECORA is non-combustible and prevents flames from spreading. Does not support combustion of other products.

5.1. Extinguishing media
Water mist, water spray – sprayer, dry chemical, foam, carbon dioxide.
Inappropriate extinguishing media – water under pressure.

5.2. Special hazards, arising from the substance or mixture – None known

5.3. Advice for firefighters – Standard protective equipment when extinguishing a fire.

6. Accidental Release Measures
6.1. Personal precautions, protective equipment and emergency procedures
Gloves, masks, protective clothing for work. Contact with skin and eyes should be avoided.

6.2. Environmental precautions
Prevent this product from release in the environment. Measures should be taken for preventing contamination of surface and underground watercourses, soil, as well as falling into the drains.
In the event of an accident and/or spill of the product, measures for localization and limitation should be taken, and the collected amount of the product should be temporarily stored into special, tightly closed and labeled containers, and after that they should be transferred to people, holding permits under the Article 37 of the Waste Management Act (publication SG, issue 53, 2012).

6.3. Methods and materials for containment and cleaning up
The spilled amount should be mechanically removed, and then the place should be washed thoroughly with water in accordance with the measures under art. 6.2.
Collected amount should be stored in special, tightly closed and labeled containers and to be temporarily stored on the territory of the company, and after that they should be transferred to people, holding a permit under the Waste Management Act (WMA).

7. Handling and Storage
7.1. Precautions for safe handling
The product should be used only according to its main purpose. Avoid skin and eye contact. Keep the package tightly closed after usage.

7.2. Conditions for safe storage, including any incompatibilities
It should be stored in ventilated and dry places, in the originally sealed containers. Temperatures lower than +5°C and higher than +40°C should be avoided.
It should be separately stored from food and drinks.

7.3. Specific Usage
There is no specific usage. It should be used only according to its main purpose.

8. Exposure Controls/Personal Protection
8.1. Control parameters – No special protection measures are necessary.

8.2. Exposure controls
8.2.1. Respiratory protection – Prolonged inhalation of fumes should be avoided.
8.2.2. Skin protection – Skin contact should be avoided, wear protective gloves. Clothing soaked with the product should be changed.
8.2.3. Eye protection – Eye contact should be avoided, wear safety glasses.
8.2.4. Common protection – It should be stored away from food, drinks and food for animals.

9. Physical and Chemical Properties
9.1. Information on basic physical and chemical properties

• Appearance – liquid paste material

• Odour – light

• pH at 20°C – 7.8

• Density – 1910 kg/m³

• Solubility – partial

• Explosive properties – Non explosive

9.2. Other information – no data.

10. Stability and Reactivity
10.1. Reactivity – No hazardous reactions.
10.2. Chemical stability – The product is stable under storage and usage in accordance with the indications.
10.3. Possibility of hazardous reactions – In accordance with section 10.1.
10.4. Conditions to avoid – Temperatures lower than +5°C and higher than +40°C should be avoided.
10.5. Incompatible materials – No data.
10.6. Hazardous decomposition products – It is unlikely to release carbon oxides at fire.

11. Toxicological Information
11.1. Information for the toxicological effects
Toxicological properties of the product are not tested. The product is classified under the conventional method in accordance with Regulation (ЕО) 1272/2008 – CLP. On the basis of its composition, the product can be defined as not having any toxic effects under proper usage.

• Ingestion – The product is not hazardous of acute poisoning.

• Inhalation – It is not considered as harmful under normal conditions.

• Skin contact – Prolonged contact may cause irritation.

• Eye contact – Prolonged and repeated contact may cause irritation and redness.

12. Ecological Information
12.1. Toxicity
Polymer dispersion data:

• Toxicity to fish: LC50 (96 h) > 100 mg/l (OECD Directive 203, static)

• Aquatic invertebrates: EC50 (48 h) > 100 mg/l (OECD Directive 202, part 1, static)

• Aquatic plants: EC50 (72 h) > 100 mg/l (OECD Directive 201)

• Micro-organisms / Effect on active sediment: EC20 (0.5 h) > 100 mg/l, active sediment (DIN EN ISO 8192-OECD 209-88/302/EEC, P. C)

On the basis of the experience, the product is not expected to be hazardous to the environment.

12.2. Persistence and degradability – No data.
12.3. Bio-accumulative potential – Accumulation in the organism is not expected.
12.4. Mobility in soil – This product is not biologically mobile.
12.5. Results of PBT and vPvB assessment – The product meets the criteria of PBT (persistent, bio-accumulative and toxic) and vPvB (very persistent and very bio-accumulative).
12.6. Other adverse effects – No data.

General information: Do not allow the product to enter into the soil or natural watercourses.

13. Disposal Considerations
Product waste, such as residual quantities and packages, should be collected into a special, tightly sealed and labelled containers, temporarily stored, and after that transferred to people holding a permit in accordance with article 37 of the Waste Management Act (publication SG, issue 53, 2012).

• Waste code, in accordance with Regulation №2 from 23.07.2014 for Waste Classification:
  08 01 20 – liquid suspensions of paints, other than those mentioned in 08 01 19

• Waste Packages code:
  15 01 02 – plastic packages

Completely empty the packages and dispose of them in accordance with the local regulations.

14. Transport Information
It is not a hazardous load, in accordance with RID, ADR, ADNR, IMDG, IATA-DGR.
It should be transported under the respective rules for transportation, concerning the respective type of transport and ensuring the safety of the load.

15. Regulatory Information
15.1. Content of volatile organic compounds /VOC/, in accordance with the Ordinance on limiting the emissions of volatile organic compounds in the use of organic solvents in certain paints, varnishes and auto reparatory products, category A, sub point c) – < 40 g/l

15.2. Classification and labelling of the product in accordance with Regulation (ЕО) 1272/2008 – CLP (full text of the codes):
GHS Pictograms: No.
Signal word: No.
Recommendations for danger (N – codes): None.
Hazard statements (H – codes): None.

Precautionary statements (P – codes):

• P101 – If medical advice is needed, have product container or label at hand.

• P102 – Keep out of reach of children.

• P262 – Do not get in eyes, on skin, or on clothing.

• P305 + P351 + P313 – IF IN EYES: Rinse cautiously with water for several minutes. Get medical advice/attention.

• P280 – Wear protective gloves/protective clothing/eye protection/face protection.

• P301 + P311 – IF SWALLOWED: Call a POISON CENTER or doctor/physician.

• P410 – Protect from sunlight.

• P401 – Store at temperatures higher than +5°C.

15.3. Legislation

National Legislation:
▪ Law of Protection from the Harmful Impact of the Chemical Substances and Preparations
▪ Environmental Protection Law
▪ Health and Safety at Work Act
▪ Ordinance №3 on the minimum requirements for safety and protection of the workers when using personal protective equipment at the workplace
▪ Waste Management Act
▪ Ordinance №2 from 23.07.2014 for Waste Classification
▪ Ordinance on the order and the method of classification, labelling and packaging of chemical substances and preparations

European Legislation:
▪ Regulation (ЕО) 1272/2008 – CLP from 16th December 2008, concerning the classification, labelling and packaging of substances and preparations
▪ Regulation (ЕО) 830/2015 from 28th May 2015

16. Other Information
16.1. Indication of changes
Format in accordance with Regulation (ЕО) 830/2015 from 28th May 2015 amending Regulation №1907/2006 (REACH) of the European Parliament.

16.2. Training Advice
In addition to the training programs on environment and health and safety of the workers, companies need to ensure that their workers read, understand, and apply the requirements of the MSDS.

16.3. Additional information
See the application(s) of exposure scenarios for the following substances:
The basic information of the exposure scenarios of the substances in the mixture are included in points 1, 2, 3, 8, 11, and 12.

16.4. Disclaimer
This safety data sheet and the data inside of it are based on industrial and commercial experience of many years and fully comply with the current active legislation of the Republic of Bulgaria and the European Union.
This safety data sheet is not intended to guarantee any specific properties and qualities of the product. The information inside is reliable, but only when the product is used in accordance with the indicated conditions and the application specified on the package and/or in the technical literature.
Responsibility for any other use of the product, including when using it in combination with another product or process, is completely under the responsibility of the user. It is understood that the user is responsible for defining the appropriate precautions and for applying the legislation concerning their own activity.