Decorit – polymer facade plaster

DECORIT

DECLARATION OF PERFORMANCE
According with Regulation (EU) №305/2011

№ 20130709-09-D

1. Unique identification code of product type:
DECORIT

2. Type, batch or serial number or other element allowing identification of the construction product as required under Article 11, paragraph 4 of Regulation (EU) №305/2011:
Polymeric facade plaster
/batch number printed on the package/

3. Intended use or uses of the construction product in accordance with the applicable harmonized technical specification, as foreseen by the manufacturer:
Acryl-polymer mixture for protective and decorative finishing coats on facades and interior walls

4. Name, registered trade name or registered trade mark and contact address of the manufacturer, as required under Article 11, paragraph 5 of Regulation (EU) №305/2011:
TERAZID Ltd.
5 „5004” Str., Gara Iskar, Sofia 1528, Bulgaria
Tel.: +3592/9799971
E-mail: office@terazid.com

5. Where applicable, name and contact address of the authorised representative whose mandate covers the tasks specified in Article 12, paragraph 2 of Regulation (EU) №305/2011:
Not applicable.

6. System or systems of assessment and verification of constancy of performance of the construction product as set out in Regulation (EU) №305/2011 for construction products, Annex V:
System 2+

7. In case of the declaration of performance concerning a construction product for which it was issued European Technical Assessment:
ETAG 004
The notified body 1020 – Technical and Test Institute For Construction Prague, has issued European Technical Assessment ETA-13/0214 according to ETAG 004.
The notified body has performed the initial inspection of the factory and of the factory production control and performs the continuous surveillance, assessment, and approval of the factory production control.
The notified body has issued EC Certificate of factory production control №1020-CPD-060037435. This certificate attests that all provisions concerning the attestation of factory production control, described in ETA 13/0214, were applied.

8. Declared performance

9. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 8.
This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.

DECORIT

Polymeric facade plaster
Acryl-polymer mixture for protective and decorative finishing coats on facades and interior walls

In accordance with the requirements of ETAG 004

PURPOSE
DECORIT is a ready-to-use finishing coat, based on acrylic dispersion with added mineral fillers with selected grain size, pigments, and preservatives.
The product is used for making fine protective and decorative coatings on facades and interior walls. The plaster creates a white or colourful waterproofed rough surface. It provides a possibility for an extremely wide variety of architectural solutions for facades and individual facade elements.
DECORIT has a wide range of colours and sizes of the structural grains, along with different options for structural formation.
The variety of colours is provided with high-quality pigments, resistant to weather conditions. The final decorative effect can be with a ‘dragged’ or ‘scratched’ structure. Colouring is according to a catalogue of 210 colours.
DECORIT is a component of the External Thermal Insulation Composite System TERAZID BIO CLIMA, approved with ETA – 13/0214.

PROPERTIES
❖ Ready-to-use
❖ Vapour-permeable
❖ Water-repellent
❖ Resistant to different weather conditions
❖ UV-resistant

PREPARATION OF THE BASE
The base must be dry, strong, and free of grease, dust, and cracks. The surfaces should be smooth and free of holes. If necessary, gaps or uneven elements of the facade should be filled with rough coating.
In case of repairing facade surfaces, unstable areas should be removed, and the areas with old paint and grease spots should be thoroughly cleaned.
Repaired sections must have the same strength and bearing capacity as the old base before priming.
The base should be primed with TERAZID G-33, at least 24 hours before DECORIT application.

CHARACTERISTICS AND TECHNICAL DATA
▪ Colour: According to catalogue
▪ Type: Homogeneous granular mass
▪ Density: 1970 kg/m³
▪ Resistance to vapour passing: µ = 205
▪ Minimal temperature of film formation: +5˚C
▪ Resistance to rain: After 24 hours*
*(at normal weather conditions – temperature of 20˚C and air humidity – 50%)
▪ Bond strength with concrete after 7 days: 1.40 MPa

Structures:

• Dragged

  • Fine grained 1.5 mm

  • Middle grained 2.0 mm

  • Grained 2.5 mm

  • Large grained 3.0 mm

• Scratched

  • Micro grained 1.0 mm

  • Fine grained 1.5 mm

  • Middle grained 2.0 mm

APPLICATION AND PROCESSING
The application of the facade plaster DECORIT can start when at least 24 hours after priming with TERAZID G-33 have passed.
When applying on large areas, the content of 2-3 buckets of DECORIT should be mixed in a bigger container. If necessary, the plaster can be diluted with the universal primer TERAZID G-33, but other ingredients should not be added.
Before the application begins, the content in the bucket should be stirred with the help of a mechanical mixer. Rusty tools are not allowed to be used.
The thickness of the coating is defined by the marble grains, which are manually applied with the help of a plastic mortarboard.

When the “dragged” variant is applied, the material should be structured with the help of a plastic mortar-board, then left for 10 minutes and finally smoothed until achieving the desired effect.
The “dragged” structure can be accomplished in different directions:

• Vertically

• Horizontally

• Diagonally

• With circular movements

When the “scratched” variant is applied, the material should be structured with circular movements, without pressure, to achieve the desired final effect.

It is recommended to work in one surface (area) without interruption. No unfinished surfaces should be left after finishing work. When applying on contiguous areas with different colours, they must be separated with paper tape to protect the already applied plaster from being stained.

Before starting priming and applying the plaster, it is recommended to cover the parts that are not going to be plastered. DECORIT should not be applied under direct sunlight or strong air drafts.

CONSUMPTION

• Dragged:

  • 1.5 mm – 2.5 kg/m²

  • 2.0 mm – 2.9 kg/m²

  • 2.5 mm – 3.6 kg/m²

  • 3.0 mm – 4.3 kg/m²

• Scratched:

  • 1.0 mm – 1.9 kg/m²

  • 1.5 mm – 2.8 kg/m²

  • 2.0 mm – 3.5 kg/m²

TOOLS FOR WORK

• Mechanical mixer

• Stainless trowel

• Plastic mortarboard

• Brush

WEATHER CONDITIONS AT WORK
The minimum 24-hour temperature of the base should not be less than +5˚C, and the maximum not higher than +40˚C.
The product should not be applied when there is rain, when the forecast is for rain, or under direct sunlight and strong wind.

FORM OF DELIVERY
Paste-form in a plastic bucket of 25 kg.

NOTES
Characteristics and technical data of the product mentioned in this Technical Data Sheet are defined at a standard temperature (20˚C) and relative humidity (50%).
In other weather conditions, the technological time for some of the processes may be shorter or longer.
The information is based on the practical experience of the manufacturer and technical tests in specialized laboratories.
Do not mix with other building materials.
All hazard and precautionary statements regarding DECORIT can be found in the Safety Data Sheet of the product.

STORAGE
12 months in the originally sealed package, stored in a dry place, without risk of freezing.

DECORIT

MATERIAL SAFETY DATA SHEET
According to (EU) 830/2015

1. Identification of the Substance/Mixture and of the Company
1.1. Product identifier – DECORIT
1.2. Application of the substance
Polymeric facade plaster.

1.3. Details of the supplier of the safety data sheet
TERAZID Ltd.
5, 5004 Street, Gara Iskar, 1528 Sofia, Bulgaria
Tel: +3592/9799971
E-mail: office@terazid.com

1.4. Emergency telephone number
EU emergency number: 112
UMHATEM “Pirogov” (toxicology) – +3592/9154409; +3592/9154233

2. Hazards Identification
2.1. Classification of the substance or mixture

• Classification in accordance with Regulation (ЕО) 1272/2008 – CLP
  The product is not classified as “dangerous.”

2.2. Label elements
Precautionary statements:

• P101 – If medical advice is needed, have product container or label at hand.

• P102 – Keep out of reach of children.

• P262 – Do not get in eyes, on skin, or on clothing.

• P305 + P351 + P313 – IF IN EYES: Rinse cautiously with water for several minutes. Get medical advice/attention.

• P280 – Wear protective gloves/protective clothing/eye protection/face protection.

• P301 + P311 – IF SWALLOWED: Call a POISON CENTER or doctor/physician.

• P410 – Protect from sunlight.

• P401 – Store at temperatures higher than +5°C.

2.3. Other hazards
None.
For all warnings and recommendations, see Section 15.

3. Composition/information on ingredients
General chemical description
Acrylic-polymer dispersion, containing mineral fillers, pigments, and modified additives.

Information of the substances in accordance with CLP 1272/2008/EC
Does not contain products, presenting in this section.

4. First Aid Measures
4.1. Description of the first aid measures

• Inhalation – Remove the person to fresh air. If the symptoms continue, immediately seek qualified medical help.

• Skin contact – Immediately rinse the area of contact with plenty of water, then wash it thoroughly with soap and water.

• Eye contact – Rinse with plenty of water for a period of at least 15 minutes and open the eyelid. Seek qualified medical help.

• Ingestion – Wash the mouth and throat. Drink plenty of water. Seek qualified medical help.

4.2. Most important symptoms and effects, both acute and delayed
None.

4.3. Indication of any immediate medical attention and special treatment needed
See point 4.1.

5. Firefighting Measures
DECORIT is non-combustible and prevents flames from spreading. It does not support combustion of other products.

5.1. Extinguishing media

• Water mist, water spray – sprayer, dry chemical, foam, carbon dioxide.

• Inappropriate extinguishing media – Water under pressure.

5.2. Special hazards, arising from the substance or mixture
None known.

5.3. Advice for firefighters
Standard protective equipment when extinguishing a fire.

6. Accidental Release Measures
6.1. Personal precautions, protective equipment, and emergency procedures
Gloves, masks, and protective clothing should be worn. Contact with skin and eyes should be avoided.

6.2. Environmental precautions
Prevent the product from being released into the environment. Measures should be taken to prevent contamination of surface and underground watercourses, soil, as well as falling into drains.
In the event of an accident and/or spill of the product, measures for localization and limitation should be taken. The collected amount of the product should be temporarily stored in special, tightly closed, and labeled containers. After that, it should be transferred to people holding permits under Article 37 of the Waste Management Act (publication SG, issue 53, 2012).

6.3. Methods and materials for containment and cleaning up
The spilled amount should be mechanically removed, and the area should be washed thoroughly with water, in accordance with the measures outlined in point 6.2.
The collected amount should be stored in special, tightly closed, and labeled containers and temporarily stored on the premises. After that, it should be transferred to people holding a permit under the Waste Management Act (WMA).

7. Handling and Storage
7.1. Precautions for safe handling
The product should be used only according to its main purpose. Avoid skin and eye contact. Keep the package tightly closed after usage.

7.2. Conditions for safe storage, including any incompatibilities
It should be stored in ventilated and dry places, in the originally sealed containers. Temperatures lower than +5˚C and higher than +40˚C should be avoided.
It should be stored separately from food and drinks.

7.3. Specific Usage
There is no specific usage. It should be used only according to its main purpose.

8. Exposure Controls/Personal Protection
8.1. Control parameters
No special protection measures are necessary.

8.2. Exposure controls

• 8.2.1. Respiratory protection – Prolonged inhalation of fumes should be avoided.

• 8.2.2. Skin protection – Skin contact should be avoided, wear protective gloves. Clothing soaked with the product should be changed.

• 8.2.3. Eye protection – Eye contact should be avoided, wear safety glasses.

• 8.2.4. Common protection – It should be stored away from food, drinks, and food for animals

9. Physical and Chemical Properties
9.1. Information on basic physical and chemical properties

• Appearance – Liquid paste material

• Odour – Light

• pH at 20˚C – 6.4

• Density – 1970 kg/m³

• Solubility – Partial

• Explosive properties – Non-explosive

9.2. Other information – No data.

10. Stability and Reactivity
10.1. Reactivity – No hazardous reactions.
10.2. Chemical stability – The product is stable under storage and usage in accordance with the indications.
10.3. Possibility of hazardous reactions – In accordance with section 10.1.
10.4. Conditions to avoid – Temperatures lower than +5˚C and higher than +40˚C should be avoided.
10.5. Incompatible materials – No data.
10.6. Hazardous decomposition products – It is unlikely to release carbon oxides in the event of a fire.

11. Toxicological Information
11.1. Information for the toxicological effects
Toxicological properties of the product are not tested. The product is classified under the conventional method in accordance with Regulation (ЕО) 1272/2008 – CLP. Based on its composition, the product is considered not to have any toxic effects under proper usage.

• Ingestion – The product is not hazardous for acute poisoning.

• Inhalation – It is not considered harmful under normal conditions.

• Skin contact – Prolonged contact may cause irritation.

• Eye contact – Prolonged and repeated contact may cause irritation and redness.

12. Ecological Information
12.1. Toxicity
Polymer dispersion data:

• Toxicity to fish: LC50 (96 h) > 100 mg/l, (OECD Directive 203, static)

• Aquatic invertebrates: EC50 (48 h) > 100 mg/l, (OECD Directive 202, part 1, static)

• Aquatic plants: EC50 (72 h) > 100 mg/l, (OECD Directive 201)

• Micro-organisms/Effect of the active sediment: EC20 (0.5 h) > 100 mg/l, active sediment (DIN EN ISO 8192-OECD 209-88/302/EEC, P.C.)

Based on experience, the product is not expected to be hazardous to the environment.

12.2. Persistence and degradability – No data.
12.3. Bio-accumulative potential – Accumulation in the organism is not expected.
12.4. Mobility in soil – This product is not biologically mobile.
12.5. Results of PBT and vPvB assessment – The product meets the criteria of PBT (persistent, bio-accumulative, and toxic) and vPvB (very persistent and very bio-accumulative).
12.6. Other adverse effects – No data.

General information: Do not allow the product to enter soil or natural watercourses.

13. Disposal Considerations
Product waste, such as residual quantities and packages, should be collected into a special, tightly sealed, and labeled containers. It should be temporarily stored and then transferred to people holding a permit, as per article 37 of the Waste Management Act (publication SG, issue 53, 2012).

Waste code, in accordance with Regulation №2 from 23.07.2014 for Waste Classification:

• 08 01 20 – Liquid suspensions of paints, others than those mentioned in 08 01 19

Waste Packages code:

• 15 01 02 – Plastic packages.

Completely empty the packages and dispose of them in accordance with local regulations.

14. Transport Information
It is not a hazardous load, in accordance with RID, ADR, ADNR, IMDG, IATA-DGR.
It should be transported under the respective rules for transportation, concerning the respective type of transport and ensuring the safety of the load.

15. Regulatory Information
15.1 Content of volatile organic compounds /VOC/
In accordance with the Ordinance on limiting the emissions of volatile organic compounds in the use of organic solvents in certain paints, varnishes, and auto repair products, category A, sub point c) – 8.8 g/l < 40 g/l

15.2 Classification and labelling of the product in accordance with Regulation (ЕО) 1272/2008 – CLP

• GHS Pictograms: No

• Signal word: No

• Recommendations for danger (N-codes): None

• Hazard statements (H-codes): None

Precautionary statements (P-codes)

• P101 – If medical advice is needed, have product container or label at hand.

• P102 – Keep out of reach of children.

• P262 – Do not get in eyes, on skin, or on clothing.

• P305 + P351 + P313 – IF IN EYES: Rinse cautiously with water for several minutes. Get medical advice/attention.

• P280 – Wear protective gloves/protective clothing/eye protection/face protection.

• P301 + P311 – IF SWALLOWED: Call a POISON CENTER or doctor/physician.

• P410 – Protect from sunlight.

• P401 – Store at temperatures higher than +5°C.

15.3 Legislation
National Legislation

• Law of Protection from the Harmful Impact of the Chemical Substances and Preparations.

• Environmental Protection Law.

• Health and Safety at Work Act.

• Ordinance №3 on the minimum requirements for safety and protection of the workers when using personal protective equipment at the workplace.

• Waste Management Act.

• Ordinance №2 from 23.07.2014 for Waste Classification.

• Ordinance on the order and the method of classification, labelling, and packaging of chemical substances and preparations.

European Legislation

• Regulation (ЕО) 1272/2008 – CLP from 16th December 2008, concerning the classification, labelling and packaging of substances and preparations.

• Regulation (ЕО) 830/2015 from 28th May 2015.

16. Other Information
16.1. Indication of changes
Format in accordance with Regulation (ЕО) 830/2015 from 28th May 2015 amending Regulation № 1907/2006 (REACH) of the European Parliament.

16.2. Training Advice
In addition to the training programs on environment and health and safety of the workers, companies need to ensure that their workers read, understand, and apply the requirements of the MSDS.

16.3. Additional Information
See the application(s) of exposure scenarios for the following substances:
The basic information of the exposure scenarios of the substances in the mixture are included in points 1, 2, 3, 8, 11, and 12.

16.4. Disclaimer
This safety data sheet and the data inside of it are based on industrial and commercial experience of many years and are fully compliant with the current active legislation of the Republic of Bulgaria and the European Union. This safety data sheet is not intended to guarantee any specific properties and qualities of the product. The information inside of it is reliable, but only on the condition that the product is used in accordance with the indicated conditions and the application specified on the package and/or in the technical literature. Responsibility for any other use of the product, including when using it in combination with another product or process, is completely under the responsibility of the user. It is understood that the user is responsible for defining the appropriate precautions and for applying the legislation concerning his own activity.